Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Largest Manufacturing Technology Community on the Web
Stay Connected:
New profile posts
-
G
gbarker wrote on cmike's profile.
Hi Cmike. I read your post from about 10-11 years ago about possibly having a manual for a Cincinnati Countour Master Mill. I am wondering if you still have that and if I might purchase a copy from you? I am really struggling to find one. Let me know,
Thanks,
Greg Barker
St Anthony, ID
Thanks,
Greg Barker
St Anthony, ID
-
M
Marek_cz wrote on Farrismek's profile.
New feed motor - what type did you used?
Are you happy with rebuild? Do you have enough power etc?
Did you consider any modern DC regulators with old motors?
(Im garage hobby machinist, so I will not make any production on it, I do not really need any high power milling machine)
Best regards
Marek
Are you happy with rebuild? Do you have enough power etc?
Did you consider any modern DC regulators with old motors?
(Im garage hobby machinist, so I will not make any production on it, I do not really need any high power milling machine)
Best regards
Marek
-
M
Marek_cz wrote on Farrismek's profile.
Hi Farrismek,
I'm Marek, from Czech Republic
I bought FUW 250/iv just as you. Can you kindly answer some questions:
Old spindle motor - was it easy for you to remove old one? I cannot pull it out of gearbox.
New spindle motor - I read you have 5,5 kW - 3000 or 1500 RPM?
Frequency converters - you use in Vector mode, or do you have vector + encoder as well?
I'm Marek, from Czech Republic
I bought FUW 250/iv just as you. Can you kindly answer some questions:
Old spindle motor - was it easy for you to remove old one? I cannot pull it out of gearbox.
New spindle motor - I read you have 5,5 kW - 3000 or 1500 RPM?
Frequency converters - you use in Vector mode, or do you have vector + encoder as well?
-
J
JD Lyles wrote on Greg White's profile.
Hi Greg, I have a MC500V with MX2 control that is in pretty good condition. Trying to get a post processor dialed in and I dont see any info on this. I had a problem with the RS232 port as I see quite a few are as well but I was able to use a Cimco V6 to go through the tape reader port.
-
T
~TABASCO~ wrote on Karl_T's profile.
Hello Sir,
Oil: My thought is, you don't get if you don't ask. Would you be interested in answering a few questions about the specifics so I dont mess up anything... I just want the best for the machine. I have an engineering back ground and extremely mechanical.... With a little guidance I can take off.... If you like, I can share phone, email, Etc.... Thank you - Jaxon
Oil: My thought is, you don't get if you don't ask. Would you be interested in answering a few questions about the specifics so I dont mess up anything... I just want the best for the machine. I have an engineering back ground and extremely mechanical.... With a little guidance I can take off.... If you like, I can share phone, email, Etc.... Thank you - Jaxon
-
O
Old_Eyes wrote on peterh5322's profile.
Hello Peter,
I am building my first RPC. I started from a pony motor design with no run or pf caps and converted it to a potential relay self starter. Though it is 7.5 hp, I am not having any trouble starting it because of the low current draw of the repulsion start motor. Would you mind taking a look at the attached balancing results and tell me what I might try next. The last line is the current configuration.
I am building my first RPC. I started from a pony motor design with no run or pf caps and converted it to a potential relay self starter. Though it is 7.5 hp, I am not having any trouble starting it because of the low current draw of the repulsion start motor. Would you mind taking a look at the attached balancing results and tell me what I might try next. The last line is the current configuration.
-
J
JA in NE wrote on SD&M's profile.
Hey. I've read some posts of yours in the past about there being a Slack group for Topsolid users. Is that group still active, and would you be able to add me to it? I've been using Top for about 6 years now programming a handful of 3 axis mills and a DMU50 doing primarily mold and die components. Awesome software, always finding new and better ways to do things with it. Thanks
-
S
Soutie wrote on Olav's profile.
Hi Olav. My name is William and I have purchased a similar machine to yours. Did you manage to find a manual on the machine or perhaps you can help me? I need to know what voltage the electric clutches in the feed gearbox run at. The wiring in my machine had been stripped out.
Would appreciate any assistance.
Would appreciate any assistance.